The Fiber Laser Obstacle Remover (also known as the Power Grid Remote Foreign Matter Removal Device) is a vital piece of high-tech equipment. This guide provides clear, step-by-step instructions for installation, operation, and essential safety checks to ensure effective and safe use.
The Laser Obstacle Clearer system consists of two primary units: the main chassis assembly and the power supply.
| Component/Feature | Description |
|---|---|
| Gimbal, Tripod, & Transmitter | The physical laser assembly for aiming and clearing. |
| Main Chassis Control Panel | Includes the Power Start Button, Power Indicator, Start Indicator, Laser Safety Alarm, and the critical Emergency Stop Button. |
This unit features an electronic screen that displays crucial information in real-time:
- Remaining Power
- Output Voltage
- System Fault Status
Follow these four steps to quickly and securely install the device on-site.
Tripod and Gimbal Assembly
Take out the tripod and set it up on stable, level ground.
Install the gimbal onto the tripod. Ensure the gimbal's bottom is perfectly aligned with the bracket slot before locking it securely.
Cable Connection (Gimbal)
Plug the gimbal cable into the corresponding interface located on the side of the main chassis.
Transmitter Attachment
Take out the transmitter. Connect it to the gimbal (aligning the bottom with the gimbal slot), then fix and lock it firmly.
Power Connection:
Plug the power cable into the port on the portable DC power supply.
Plug the other end into the port on the main chassis outer box.
(Note: The power cable is non-directional, so either end can connect to either unit.)
Operation is managed through a dedicated tablet device after initial hardware setup.
Connect Remote Tablet: Open the settings on the dedicated tablet and connect to the internal LAN WIFI broadcast by the laser obstacle clearer host.
Measure Target Distance: Use a rangefinder to precisely measure the distance between the equipment and the target obstruction.
Pre-Operation Safety Check (Mandatory): A drone must be used to confirm the surrounding area is safe and clear before proceeding with any laser operation.
Aim at Target: Use the tablet's direction keys to move the launcher. Aim at the obstacle, using the 30x magnification lens for critical focus.
Set Distance Parameters
- Navigate to the “Distance" menu.
- Select the distance measured by the rangefinder.
- Click “Execute" to confirm the parameters.
Set Power Level
- Open the “Power" menu.
- Select the appropriate power setting for the target material and distance.
- Click “OK".
- Start Clearing: Use the direction keys to move the laser point to clear the target.
After completing the cleaning work, a careful inspection of the surrounding environment is essential to prevent fires.
- Are there any remaining flames or sparks?
- Is there any flammable material that has been scorched by high temperature?
- Are there other factors present that could potentially cause a fire?
- Use water or a fire extinguisher to completely extinguish any flames or sparks.
- Move any potentially flammable materials away from hot areas.
- Cover potential fire hazards with soil or sand if necessary.
Proper maintenance ensures the laser device remains reliable and effective.
Tools Required:
- Powder-free rubber gloves
- Lint-free cleaning cloths and cotton swabs
- Pure ethanol or alcohol
- Compressed air
Cleaning Procedure:
- Gently wipe the laser aiming head housing, the platform, and the display screen.
- Always refer to your product instructions for detailed, periodic maintenance requirements.
Q: Why is the device not starting?
A: This usually happens if the Emergency Stop is pressed, the key switch is off, or core components are not in standby state. Check the emergency stop switch, key switch, platform base limits, platform, and laser status to ensure they are all ready.
Q: Why is there no display on the remote control screen?
A: The remote control screen may be off due to the switch being turned off, a problem with the data cable or SD card, or the battery being discharged. Check the remote control switch, verify the data cable connection and SD card status, and check the remote control battery level.
Q: The laser does not emit, and the screen displays "Abnormal Temperature."
A: The laser has automatically shut down because it is overheated. Shut down the system and restart after a few minutes of cooling. Crucially, check the main cabinet cooling fan to ensure it is not blocked and is starting correctly.
Q: The laser does not emit, but the Power Display is normal.
A: This indicates the laser is in overheating protection (the laser light is on, but the power light is off). Shut down the device for a few minutes to cool down, and then restart the system.
Q: Why is the platform unresponsive?
A: The platform won't respond if the main device is off, the antenna is unplugged, or there is an issue with the remote control (switch off or battery discharged). Check if the device is powered on, confirm the antenna is plugged in, and verify that the remote control switch is on and the battery is charged.